Manley Chinook MM/MC Phono Stage Includes (4) NOS Amperex Holland 6922's from Andy at Vintage

I purchased this a few months ago and have purchased a new preamp with a built in phono stage. Excellent sounding and very flexible with user adjustable dip switches on the back to customize gain/loading. MM gain =45 MC gain equals 60. All tubes are upgraded NOS Amperex Holland purchased from Andy at Vintage Tube Services. These are Super MIC grade, his best. $500. in NOS tubes. See below specs from Manley web site:

• Vacuum Tube Complement: 6922 x 2 (gain stage) plus 6922 x2 (output stage). Any 6DJ8, 7308, ECC88 types may be used.


• Unbalanced Input and Output connections via Manley Teflon® & Gold plated RCA jacks


• Automatic Mute Timer: On initial power up output jacks are muted for approximately 45 seconds. Automatic mute circuit allows tubes to warm up and circuitry to settle. At power down, output jacks are immediately muted.


• Input Termination Capacitance (MM/MC): 3-position user-selectable capacitor values of 50pF, 100pF, and 200pF yield resultant combinations of: 50, 100, 150, 200, 250, 300, and 350pF


• Moving Magnet Input Impedance: 47k Ohms, fixed


• Moving Coil (MC) Input Impedance: 5-position user-selectable resistor values of 50, 100, 200, 400, and 800 Ohms. 

• Gain: Internal DIP switches select 45dB or 60dB


• Deviation from RIAA curve: Less than ± 0.5 dB from 20Hz to 20kHz at any gain setting. Typically less than ±1dB from 10Hz to 100kHz.


• Distortion (THD+N) (47k Ohm Input Termination, 45dB gain, 1kHz sine, 0dBu output): Typical 0.010% THD+N, into 100k Ohm load, BW = 100Hz-22kHz


• Distortion (THD+N) (47k Ohm Input Termination, 45dB gain, 1kHz sine, 0dBu output): Typical 0.030% THD+N, into 600 Ohm load, BW = 100Hz-22kHz


• Dynamic Range (MM input, Gain set to 45db, 200 Ohm source): 91dB @ 1kHz, 0.1% THD+N, BW = 22Hz-22kHz


• Dynamic Range (MM input, Gain set to 45db, 200 Ohm source): 107dB @ 1kHz, 1.0% THD+N, BW = 22Hz-22kHz


• Noise Floor at 45dB gain setting with shorted input: -84 dBu, A-weighted


• Noise Floor at 60dB gain setting with shorted input: -75 dBu, A-weighted


• Maximum Input at 45dB gain setting with 20 Ohm Source Z @ 1kHz into 10 kOhm load: 250mV RMS = +34.5 dBu @ 1% THD+N BW=22Hz-22kHz


• Maximum Input at 60dB gain setting with 20 Ohm Source Z @ 1kHz into 10 kOhm load: 40mV RMS = +34.2 dBu @ 1% THD+N BW=22Hz-22kHz


• Maximum Output: +37dBu @ 1kHz, 1.5% THD+N into 100 kOhm load


• Output Impedance: 91 Ohms


• Minimum Recommended Load: 2500 Ohms


• Internal Power Supply: Fully regulated linear B+, Heater, and control voltage rails.


• Operating Mains Voltage: Units are built for original destination country's mains voltage: 100V, 120V, or 220-240VAC as indicated on the serial number badge.


• Power Consumption in Standby mode: 1 Watt (8.0mA @ 120VAC)


• Power Consumption: 42 Watts (345mA @ 120VAC)


• Mains Voltage Frequency: 50~60Hz


• Power Transformer: Toroid contruction for low radiation.


• Mains Fuse for 100V operation:
  800mA SLO-BLO Glass Littlefuse Series 239 size 5mm x 20mm


• Mains Fuse for 117V-120V operation:
  800mA SLO-BLO Glass Littlefuse Series 239 size 5mm x 20mm


• Mains Fuse for 220V-240V operation:
  400mA SLO-BLO Glass Littlefuse Series 239 size 5mm x 20mm


• Standby Transformer Fuse for all voltage operation 100V-240V: 10mA, SLO-BLO, MDL type size 1/4" x 1 1/4"


• Badge Lamp: LED illumination


• Dimensions: W=19", L=11", H=3 1/2"


• Shipping Weight: 15 Lbs.